Ignition Accessories

!
RCEXL_IGN1_90

RCeXL (90 degree cap) Ignition for CM-6 spark plug

Rcexl replacement single ignition set for gas engines using a CM-6 (10mm) spark plug.  Spark Cap angle is 90 degrees.

Can be used for e.g. DLE, MVVS, RCGF, NGH and many other engines.

CDI contains extra output for RPM measurement.

Delivery includes sensor.

RCEXL_IGN1_120

RCeXL (120 degree cap) Ignition for CM-6 spark plug

Rcexl replacement single ignition set for gas engines using a CM-6 (10mm) spark plug.  Spark Cap angle is 120 degrees.

Can be used for e.g. DLE, MVVS, RCGF, NGH and many other engines.

CDI contains extra output for RPM measurement.

Delivery includes sensor.

RCEXL_IGN2

RCeXL (90 degree cap) Twin Ignition for CM-6 spark plug

Rcexl replacement ignition set for DLE170, DLE111, DLE60, RCGF40, RCGF50, RCGF60, RCGF111 and other twin cylinder engines.

CDI contains extra output for RPM measurement.

Delivery includes sensor.

DLE_IGN1_90

Original DLE (90 degree cap) ignition module

Original DLE single ignition set for DLE20, 30, 55. Spark Cap angle is 90 degrees.

CDI contains extra output for RPM measurement.

DLE_IGN1_120

Original DLE (120 degree cap) ignition module

Original DLE single ignition set for e.g. the DLE20RA, 35RA, 55RA. Spark Cap angle is 120 degrees.

CDI contains extra output for RPM measurement.

ROTOIGN2535

ROTO 25 and 35 Ignition System

ROTO replacement ignition set for ROTO 25 and 35 engines

 

ROTOIGN35FS

ROTO 35FS Ignition System

ROTO replacement ignition set for ROTO 35FS 4-stroke engines

 

ROTOIGN5070

ROTO 50 and 70 Ignition System

ROTO replacement ignition set for ROTO 50 and 70 Twin engines

 

ROTOIGN85

ROTO 85 Ignition System

ROTO replacement ignition set for ROTO 85 Twin engines.

Delivery is without sensor.

 

ROTOIGN130

ROTO 130FS Ignition System

ROTO replacement ignition set for e.g. ROTO 130 engines.

Delivery is without sensor.

 

ROTOSENSOR

ROTO Sensor for Ignition System

ROTO replacement sensor for ignition system.

 

RCEXL-ICM6

CM6 Irridium Spark Plug

CM6 10mm Irridium Spark plug for gas engines from DLE, DLA, RCGF, NGH etc.
DLE-SPC90

Spark Plug Cap for CM-6 (90 degree cap)

DLE-SPC120

Spark Plug Cap for CM-6 (120 degree cap)

BPGE3004

Ignition Mini Tachometer

Mini tachometer from Rcexl for use with electronic ignition systems like the CDI.

Indicates up to 30000 rpm.

BPGE3003

Ignition hall sensor test kit

Check the hall sensor and ignition timing of electronic ignition systems using this test kit from Rcexl.

New type, not exactly equal to picture.

 

BPGE3002

Ignition Tester

This is a timing and testing kit for RC Gas/Petrol engines using CDI ignition .

This kit,will allow you to check ignition working conditions, without the need to start the engine.

Engine speed in between the 400RPM-20000RPM. Can be used to check radio interferences and the radio range check.

 
WIKERC_IBEF21

IBEF Ignition Battery Eliminating Filter, WIKE R/C, Down and Locked

This device from WIKE R/C Products will allow you to safe the weight of an extra ignition battery and provides an integrated engine kill switch.The IBEF is designed to be plugged into the receiver and run the ignition from the receiver batteries or power system. Ignition power can be turned on and off by assigning the channel the IBEF is plugged into to a 2 position switch. A spare receiver channel is needed to use this switch.  A remote mountable led is included to indicate ignition arming status.

EME55-STARTER

Electric starter for the DLE55, EME55 etc., auto start kit

Suitable for e.g. the DLE55 and EME55.

Remote start your engine with a switch of your transmitter. This is possible when using an electric on-board starter.

BPA14-10

Spark Plug Adapter 14mm -> 10mm

Spark Plug adapter from 14mm to 10mm.
BPGE3008

Safety Clips or Servo Cable Holders (10 stuks)

Safety clip voor servo connectoren. Zorgt ervoor dat de twee connectoren niet meer van elkaar af kunnen gaan.

Deze clips zijn noodzakelijk waar bijvoorbeeld een verlengkabel gebruikt moet worden.

HWUBEC3

UBEC 3A, 2-6 cells LiPo, selectable output voltage 5/6V

The 3A-UBEC is a switch-mode DC-DC regulator. This UBEC can be used to supply the power for the electronic ignition system of a gas engine or the receiver and servos. 

The 3A-UBEC is a switch-mode DC-DC regulator. This UBEC can be used to supply the power for the electronic ignition system of a gas engine or the receiver and servos. 

Input Voltage:    6 - 26V  (2 - 6 cells LiPo)
Output Voltage:  5 or 6V (manual selectable)
Output Current:  3A continuous

BPST1005

Medium Power Switch

Power switch between the battery and the UBEC, CDI or receiver. 

2-pin JST in- and JR Output connectors. JR charge jack.

Can be used with NiCd, NiMh, LiPo and LiFe batteries.